ARP 1601 Sequencer
A 16-step voltage generator with a quantizer that rounds to the nearest twelfth of a volt — and a service manual that tells you exactly how to keep it alive.
In a 2006 comparison of ARP 2600 emulations, Sound on Sound (August 2006, p.154) noted that the sawtooth waves of the two instruments under test sounded very similar despite marked visual differences in their waveforms — a reminder that the ARP sound is about more than what an oscilloscope shows.
Overview
The ARP 1601 is a 16-step sequential voltage generator, and the first thing a collector notices is how completely it assumes you're already speaking ARP's language. Each of the 16 steps gets its own voltage level slider, sweeping the output from 0 to +10 volts. Those outputs feed a quantizer that rounds the sequence's voltage to the nearest whole twelfth of a volt — which is what makes the thing musically usable, since ARP tuned its products to a 1 volt per octave standard, one-twelfth of a volt per semitone. The quantizer isn't a guess about intent; the manual states it plainly as the reason the feature exists.
The mode switch is where the 1601 earns its keep. Run it in 16 X 1 and channels A and B are common, one long sequence. Flip to 8 X 2 and banks A and B — steps 1 through 8 and 9 through 16 — sequence in parallel as two separate eight-step lines. Internally that's a four-bit counter feeding a decoder for 16 positions, or a three-bit code when the banks split.
The clock is a low-frequency voltage-controlled oscillator, and it's more flexible than the step count suggests. It runs 0.2 Hz to 100 Hz, with pulse width variable from 10% to 100% (less 5 msec.), and a PWM input jack that accepts 0 to +10 volts. There's an FM input with a sensitivity of 2V/oct maximum, prewired to Gate Bus 1, so an external control voltage can speed the clock up. The clock can be started, stopped, gated, or speeded up manually or externally — step, reset, start, stop, and start/stop jack inputs all accept a +3 V to +10 V gate. A clock output puts out a +14 V pulse wave for triggering external envelope generators.
The gate architecture is the part that separates the 1601 from a plain analog step box. Position gates provide a constant +10 volts for as long as the sequencer sits on a selected position, and those outputs are bused to one of three position gate outputs — Gate 1, 2, or 3, selected by the position gate assignment switches on the panel. The manual's own framing is that each step can generate different voltage gates across the three busses, which effectively turns the sequencer into a smart envelope generator. There's also a dedicated Position 1 output that supplies a +14 V gate on position 1 only, for syncing additional sequencers or synthesizers, and a clocked gate out that lets you select particular position gates from Gate Bus 1 with pulse-width control from the clock.
The sequencer outputs themselves provide 0 to +10 volts of analog CV. The quantized outputs run 0 to +2 volts in 1/12-volt increments — a range that surprises people who expect the full sweep to be quantized, so it's worth knowing before you patch. The A and B quantized outputs are common in 16 X 1 mode and separate in 8 X 2. A CV input lets an external voltage, a keyboard for instance, sum with the sequencer's voltage to shift the key the sequence plays in. The quantizer inputs are prepatched to the sequencer outputs but broken out on jacks, so external voltages can be quantized too.
The performance controls go further than the step sliders. There's a sequential/random mode switch — in random mode the randomizer circuit advances the counter at an extremely high frequency, and for each cycle of the low-frequency clock a position number is memorized and held, so the memorized positions come out random. A skip/reset function lets particular positions, from Gate Bus 3, either skip past or reset on particular positions. A trig/gate switch changes behavior: in trigger mode the sequencer is triggered on, while in gate mode it runs only while the start button is held. A foot switch jack on the rear panel supplies a +14 V gate to the foot switch out jack on the front. Each step's LED lights when that step is gated.
Power is worth a note for anyone buying blind. The service manual lists line voltage at 100 to 130 V AC and line frequency at 50-60 Hz — this is a US-market document, and the manual's own troubleshooting guidance is to unplug the sequencer and mount the power supply on the outside rear panel before poking around, which tells you something about how ARP expected these to be serviced in the field. Disassembly is documented in detail: eleven bolts and all the slider knobs come off the front panel, then the slider shafts get pushed gently until the main board pops loose. The lower jack board comes out by removing the jack nuts on the lower front panel and pulling the bottom of the power switch out so the board clears it. That's more disassembly guidance than most vintage gear ever gets, and it's a real advantage for a unit this age.
What the 1601 does not give you is a modern sequencer's conveniences. The quantizer's 0 to +2 V output range is narrower than the unquantized 0 to +10 V, and the maximum unquantized control voltage output is +12 V against a maximum gate output of +14 V — the kind of detail that matters when you're patching it into something that expects a different standard.
For collectors, the 1601 is one of the ARP pieces where the documentation is as valuable as the hardware. The service manual — Document Number 9001901, © September 1976, ARP Instruments, Inc., 320 Needham Street, Newton, MA — covers theory of operation, circuit descriptions down to the counter/latch and mask circuits, test points, calibrations, schematics, and a full parts list including the CD4042AE quad clocked D latch and CD4028AE octal decoder at the heart of the position logic. That level of documentation means a dead 1601 is a repairable 1601, which is not something every 1970s sequencer can claim.
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.
Related Models
- ARP 1601 (1976)
- ARP Sequencer 1601
- Alesis MMT8
- Korg Electribe (1999-)
- Korg SQ-64
- Korg SQD-1
- Oberheim DSX
- Sequential Circuits Model 800 (1975)
- Roland MC-202 MicroComposer (1983)
- Roland MC-505 (1998)