Electro-Voice S-1503ER

A 300-watt, biampable three-way stage box built around a vented midrange that E-V swore wouldn't honk.

Overview

Electro-Voice's own manual describes the S-1503ER in one breath: "a 300-watt, three-way, high-efficiency stage system." That is the whole pitch, and for a working stage monitor it is a good one. The model carries the spec number 1009-1456, and the surviving documentation comes out of the Electro-Voice, Inc. offices at 600 Cecil Street, Buchanan, Michigan 49107. Manual-site listings give the full name as "Electro-Voice Speaker System S-1503ER Biampable Three-Way," which tells you the bi-amp capability was considered a headline feature rather than a footnote.

What makes the S-1503ER interesting is not the wattage figure — plenty of boxes claim 300 watts — but the driver arrangement behind it. The system is genuinely three-way, with a 15-inch woofer at the bottom, a vented midrange covering the middle, and a constant-directivity horn handling the top. The crossover between those sections is a 12-dB-per-octave network, a second-order slope that is gentle enough to keep the drivers integrated without the phase drama of steeper filters. The high-frequency horn is specified at 90° x 40°, a pattern that is wide in the horizontal plane and tight vertically — the standard recipe for a box that can cover a stage without spraying sound into the ceiling.

The midrange is the part E-V's literature keeps returning to. It is a vented midrange, and the manual is explicit about why it exists: the vented design bridges the gap between woofer and high-frequency section while avoiding the "honky" quality and upper-range beaminess that small-format horns often bring when crossed below 1,000 Hz. That is a specific engineering claim from the manufacturer, not an independent verdict, but it points at the real design tension in any three-way stage box — the midrange is where cheap systems fall apart, and E-V built this one around a non-horn solution.

Frequency response is documented under a stated measurement condition — 10 feet on axis, swept one-third-octave, half-space anechoic environment — and the manual gives 62-20,000 Hz for that measurement, with -3 dB points at 62-18,000 Hz and -10 dB points at 40-25,000 Hz. The same is true of distortion: the manual prints figures including what reads as "10,000 Hz: 3.1%" and a "Distortion, 0.01 Full Power Input" line, but the surrounding OCR is garbled enough that the labels can't be trusted without the original PDF in hand. Collectors chasing exact numbers on this one will need the paper manual.

Key Features

VMR Vented Midrange Bridging Woofer and Horn

The heart of the S-1503ER is the vented midrange — E-V's VMR, listed by name in the Manualzz documentation for the model. In a conventional three-way, the midrange is either a cone that struggles to meet the horn or a small horn that honks when pushed down toward the woofer's upper range. The VMR is a third path: a direct-radiator midrange with a vented rear chamber, described in the manual as capable of "large amounts of acoustic output from a small package" without the beaminess and honky coloration E-V associates with small horns. It is a 10-inch midrange, and it sits between the 15-inch woofer and the compression driver on top. Whether it fully delivers on the no-honk promise is a judgment the surviving documentation does not let anyone make — there is no independent review of this specific box in the record — but the design intent is unusually clear for a stage monitor of its class.

90° x 40° Constant-Directivity Horn

The high-frequency section uses a 90° x 40° constant-directivity horn. The horizontal coverage is wide enough to throw across a stage or a small room; the vertical pattern is deliberately narrow so the energy goes where the audience is and not into the ceiling or the floor. Constant-directivity horns hold their pattern across their passband rather than narrowing as frequency climbs, which matters in a monitor where the singer needs the same tone whether they are dead center or off to the side.

12-dB-per-Octave Crossover

The crossover slope is documented at 12 dB per octave. That is a second-order electrical slope, gentle by modern DSP standards, and it is the kind of filter that lets the drivers overlap and blend rather than handing off abruptly. For a passive three-way, the choice is a practical one — steeper slopes cost more components and introduce more phase shift, and a 12-dB network is easier to build with the kind of reliability a stage box needs.

Biampable Design

The S-1503ER can be run mono-amplified through its internal passive crossover or converted to bi-amplification. Manualzz's listing leads with "Biampable Three-Way," and the manual describes the conversion as something the system "may be easily converted for." For a working sound company, that flexibility is worth real money — the box can go out on a small gig with one amp channel per cabinet and come back into a bi-amped rig when more headroom is needed. The E-V manual also contains a fragment claiming "To our knowledge, Electro-Voice was the first U.S. manufacturer to develop and publish a power test closely related to real-life conditions," though the sentence is cut off in the surviving OCR.

Built for the Road

The materials list for the S-1503ER includes fiberglass batt insulation cut at 12" x 24", the kind of internal damping that keeps a vented enclosure from getting tubby. Beyond that, the documentation records an enclosure built of Road-Wood™ covered with densely woven, abuse-resistant black carpeting, with a grille assembly fastened to the enclosure using four sturdy dual-lock fasteners. What is documented is that this was sold as a stage system, which tells you the enclosure was expected to be moved, loaded, and stacked rather than parked in a living room.

eBay Listings

SHOP ELECTRO-VOICE S1503ER ON EBAY

As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.

Related Models