Altec 288B Driver Speaker
A high-output compression driver built for power and presence, not finesse. Horn enthusiasts still seek it out despite its age and quirks.
Overview
The Altec 288B Driver Speaker wasn't made for bookshelf listening or quiet jazz nights. It was built for projection, to cut through noise in large venues, broadcast systems and high-level reinforcement setups, where clarity under load mattered more than flat response. It was introduced at least as early as 1953, with examples documented from that year. Altec marketed it for use in "high level music, speech reinforcement and paging systems of the highest quality." No official frequency response or sensitivity figures survive in the documentation. Its role suggests midrange punch and efficiency rather than extended highs or deep bass. Owners report pairing it with Western Electric and Jensen systems, and it is often repurposed into modern horn projects.
Power handling is the most persistent technical question around the 288B. The 1957 Altec catalog lists both an "eight watt power handling capacity" and a "40 watt power capacity." That is a clear conflict, and it has never been officially reconciled. Given Altec's conservative engineering practices of the era, it's plausible that the 8-watt figure refers to continuous thermal handling, while the 40-watt claim might reflect short-term peak or mechanical capability. Audio (January 1964, p.22) noted that Altec manufactured a smaller version of the 288B, the 802D, which had curved-mouth horns available for it. Either way, users are advised to be cautious, since exceeding conservative limits risks damaging the voice coil, a failure mode already documented in owner reports. A Facebook user in January 2026 noted testing four 288B units, all showing "DCR is mega ohms," a sign of open circuits, likely from degraded insulation or overheating over decades of use or misuse.
Key Features
Compression Driver for High-Level Systems
The 288B is a compression driver meant to be mated with large horn throats. Its construction favors durability and acoustic output over neutrality, which suits installations where sound must travel long distances and stay intelligible. Unlike modern drivers optimized for linearity, it leans into the characteristics of its era: high efficiency, moderate power handling, and a rugged build suited to continuous operation. No sensitivity rating is documented in surviving materials, but its use in large-scale reinforcement systems implies a design focused on maximizing SPL per watt.
Modified Use in Horn Systems with ~200Hz Cutoff
The 288B is a driver, not a complete speaker, but it has found a second life in modern DIY horn projects. One documented system, described on Bjørn Kolbrek's horn speaker research site, uses modified Altec 288B drivers in a horn enclosure with a cutoff frequency of approximately 200 Hz. That suggests the driver can work in full-range horn systems when paired with appropriate low-frequency support and crossover design. A diyAudio thread discussing a 288B in a plane-wave tube noted interest in crossing over in the 5-7 kHz range. That implies the driver can extend reasonably high, but its best use is in midrange-heavy applications.
24 Ohm Variant (288B Hollywood)
A variant known as the "288B Hollywood" appears in user discussions, distinguished primarily by its impedance. One Facebook post from October 2023 confirms using a "288B holywood (24omh)" with a 12-watt amplifier, suggesting a higher impedance version tailored for specific installations or transformer-matched systems. Standard impedance for the base 288B remains undocumented, but general Altec practice of the time often included multiple impedance options for different distributed line applications. D.C. resistance, per a commonly cited rule of thumb mentioned in enthusiast forums, is approximately 80% of the rated impedance. A 24-ohm unit would likely measure around 19 ohms DCR when functional.
Historical Context
The Altec 288B emerged when public address and theater sound systems were moving toward higher fidelity and greater output. Exact production years are not fully documented, but a listing on HifiShark references "2 Beatifull Altec 288B from 1953," confirming its presence by that year. It was positioned as a premium driver for critical installations, competing with Western Electric and Jensen components. Those brands are frequently mentioned alongside the 288B in current listings and restorations. Its design reflects Altec's philosophy of building components for real-world durability, not just lab measurements. The original materials publish no frequency response or distortion data, so performance was often judged by subjective clarity and output rather than objective metrics.
Collectibility & Value
Today the 288B trades in a niche collector and DIY audio market. In recent listings, a pair of Altec 288Bs without diaphragms sold for $1,699, while another set described as "2 Beatifull Altec 288B from 1953" fetched $2,499. Condition, completeness and provenance clearly affect value. Failures are common, especially open voice coils, as multiple reports of DCR readings in the mega-ohm range show. Repair is sometimes possible, since original Altec 288 diaphragms have been spotted for sale on Facebook. Enthusiasts continue to compare the 288B with the 288C, as in an audioheritage.org thread titled "Altec 288B vs 288C," though detailed performance differences remain undocumented in available sources. One owner reviewing an impedance plot on the same forum praised the results as "exceptionally good looking curves / by any standard (old or new)."
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.