Euphonix CS2000B
A digitally controlled analog broadcast console whose mixing surface carries all the intelligence — and whose audio tower keeps passing sound even after the desk goes dark.
Overview
The CS2000B is the kind of console that makes you rethink what "analog" and "digital" mean in a control room. Euphonix built it as a digitally controlled analog desk: an almost traditional analog audio path married to a compact, fast digital control surface. The processors live in the mixing surface and send commands down to the audio tower, where they're decoded and applied to the analog processing circuitry. That split architecture has a practical payoff collectors and engineers both appreciate — if the mixing desk is shut down, the tower keeps passing audio. A power failure sends the control system into a minute-or-two reboot, but the tower itself comes back roughly one second after power returns, in the same state it was in when it went down. For a broadcast desk, that's not a spec-sheet nicety; it's the difference between dead air and a show.
This was a console built with broadcasters specifically in mind, and the field report published in Broadcast Engineering (the review that anchors most of what's documented about the model) makes the accommodations plain. The 24 outputs that Euphonix's recording-studio console design used to feed 24-track machines were reassigned here as mix-minus sends. Active fader speaker muting, tally lights, GPIs for tape-machine starts tied to fader logic, electronic scribble strips, redundant power supplies, expanded external monitor inputs (32 stereo) and external router control — the last arriving with software version 2.6 — round out the broadcast-focused feature set. The reviewer's summary was blunt about the result: with all of these features, the board fits comfortably into a broadcast control-room environment.
The channel architecture is where the CS2000B gets genuinely interesting. Each channel strip carries a double row of faders and offers six inputs — M1, M2, and L1 through L4 — assignable in any combination to either or both faders. The M1 and M2 inputs handle levels from mic to line; L1 through L4 are fixed at +4dBu. Faders can run in stereo, mono, stereo-reverse and other modes, be assigned to either of two main output buses, or routed to aux sends, direct outs, or three utility outputs known as Outs 1–3, most of them pre- or post-fader selectable. The practical upshot, as the field report put it, is that with a little thought about source assignment the board fits 56 faders into what traditionally would be only 28. All channel strips are identical, so setups copy from one strip to another, and whole sections — "blocks" like auxiliary bus assignments — can be copied too, which speeds up snapshot building considerably. The trade-off is honest: each strip offers significantly more capability than a traditional console, though it stops somewhat short of being two channels in one, particularly when it comes to EQ or dynamics per strip.
The center section is the digital studio controller, or DSC, and it can be located anywhere on the mainframe — as can the channel strips, in groups of four. That means the CS2000B's layout can be changed or expanded after installation to suit changing needs, a rarity among large consoles. Except for the pots, every function on the channel strips can also be driven from the DSC and master section. All rotary controls on the DSC are shaft encoders, and most of its push buttons are the large, illuminated, patented, industrial-strength variety. Indicators and controls change function based on the current task, and a healthy number of controls sit unassigned in anticipation of future software. The field report noted that although this assignable approach may seem unorthodox, operators at the station running the review board had little trouble adjusting to it. Studio Sound (July 1995, p.56) likewise found the control surface intuitive enough that a session could comfortably be run on it — and was pleased to find the sound first rate, noting that the console's very familiarity, rather than an outlandish look, was one of its strongest points.
Under the hood, the digital control system is built around distributed processing — processors scattered throughout the system so that if a subsystem crashes, it doesn't take down the whole system. In a real-time desk, speed is everything: lift a fader and you expect the level to move without delay. The field report's verdict was that every control acts as if mechanically connected to its function. A DOS-based computer loads system software, stores setup information and drives the LCD screen on the DSC. If that computer dies, the graphics screen goes dark and new setups can't be loaded, but the system is otherwise unaffected — an important purchasing consideration, since some other automated consoles of the era passed operational data through a PC, and if the PC locked up, so did the show. The PC is still central to the CS2000B's ability to store and recall setups, and snapshot recall is fast: one or two keystrokes pull up one of 50 snapshots in each title, with recall time under one frame, fast enough to do live. Snapshots can capture everything from dynamics setup and EQ profiles to IFB configuration and source mapping — every level and switch position except monitors — and MIDI program changes can be made as part of a snapshot.
I/O runs entirely through bantam patchbays made specifically for Euphonix, interfacing to the board and the outside world via high-density Elco connectors; Euphonix supplies the interconnection from console to patchbays. Elco is more common in recording than broadcast, but the field report found them easy to install and quite robust. The one exception is time code, fed directly into the processing tower via XLR — apparently to keep time code and audio as far apart as possible. Inputs can arrive through a Euphonix 48x48 mic router (the CUBE) or a house router, and with that configuration a complete recall of all board settings between consecutive live shows becomes possible, to the point where every show can be produced without ever changing a patch cord.
Documentation is extensive — schematics for almost every circuit are included, with the notable exception of several proprietary designs drawn as black boxes. The honest caveat, straight from the field report, is that software documentation lags behind the latest code release, though release notes accompany each software version and Euphonix even publishes a list of known bugs alongside the fixes. The development team was described as capable and responsive, and the architecture was designed so enhancements can be retrofitted to consoles already in the field. Euphonix was still shipping new software to all customers without annual software maintenance agreements — a policy the reviewer flagged approvingly. The board's own control system, in the report's words, proved well-designed, reliable and effective.
For collectors, the CS2000B occupies an odd but compelling spot. It's a large, digitally controlled analog console with snapshot automation, immediate and quiet recall, and high-quality audio performance — the field report's performance summary reads like a checklist of what a modern broadcast room wanted in the mid-1990s. The WFLD-TV installation documented in that report was serial number 1 in the new broadcast line, chosen at the end of 1994 and on the air by September 1995. Because the design was built for retrofit and expansion, surviving examples retain the potential to be reconfigured and updated rather than frozen. What the documented record does not cover is current market pricing, common failure points, or parts availability — anyone chasing a CS2000B today is largely on their own for service intelligence, and should expect to lean on the schematics that ship with the console. That documentation package is, in its own way, as much a part of the instrument as the faders.
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.