AMS DM2-20 (1976)
The first product from Advanced Music Systems, built by a musician-engineer who wanted tape phasing without the tape.
Overview
The DM2-20 feels like it rolled off the bench the day after someone figured out how to make digital delay lines do something musical. It wasn't built to be flashy or user-friendly. Mark Crabtree, the founder of Advanced Music Systems, wanted the swirling phase shifts of analog tape machines without the maintenance, the wear, or the cost of endless reels. In 1976, that was borderline heresy. Tape was king, and its artifacts - flutter, phase drift, harmonic smear - were considered part of the magic. The DM2-20 asked what if you could keep the magic and ditch the mechanical headaches. It doesn't emulate tape in a vague way. It models the physics of two independent tape paths with variable speed modulation. It doesn't just mix a delayed signal with the original like most phasers of the era. It uses dual delay lines to simulate the timing differences between two real tape machines running slightly out of sync. The stereo image breathes, wobbles and swirls.
It's not a flanger, not a chorus, not a garden-variety phase shifter. It's a tape phase *simulator*. The Electro-Harmonix Small Stone and the MXR Phase 90 carve out scooped, resonant notches that sweep up and down the frequency spectrum. The DM2-20 creates a more organic, unpredictable motion, closer to what happens when you manually nudge the flange of a tape reel. The modulation is deeper, slower, and less periodic. Plug in a clean electric guitar, and it sounds like the amp is slowly rotating in a cathedral. Run a synth pad through it, and the sound folds in on itself, then unravels like smoke. On a vocal, the singer ends up inside a shimmering bubble that pulses with the rhythm of the track.
For all its innovation, the DM2-20 never became as common as the units that followed it, like the DMX 15-80S or the RMX 16. It was too early, too niche, and too expensive for most studios in the late '70s. But those who used it, Paul McCartney among them, saw its potential right away. It was a new way of thinking about time-based effects. It was AMS's first product, and it was a personal solution to a real problem, not a box designed by committee. It suited producers looking for cleaner, more controllable alternatives to analog tape manipulation.
Specifications
| Manufacturer | Advanced Music Systems (AMS) |
| Production Years | 1976 |
| Original Price | Not available |
| Type | Tape Phase Simulator |
| Technology | Analog delay lines with digital control |
| Delay Lines | Two independent analog delay lines |
| Modulation Source | Variable speed modulation simulating tape flutter |
| Inputs | 1 x XLR balanced, 1 x 1/4" unbalanced |
| Outputs | 1 x XLR balanced, 1 x 1/4" unbalanced |
| Frequency Response | 20Hz - 20kHz |
| Dynamic Range | Greater than 90dB |
| THD | Less than 0.05% |
| Power Supply | Internal linear power supply |
| Voltage | 115V or 230V selectable |
| Weight | Approx. 10 kg (22 lbs) |
| Dimensions (W×H×D) | 483 mm × 88 mm × 356 mm (19" × 3.5" × 14") |
| Rack Size | 19" 2U |
| Made In | United Kingdom |
Key Features
Dual Analog Delay Lines for True Tape Simulation
Most phasers use a series of all-pass filters to create phase shifts, which gives a repetitive, almost mechanical sweep. The DM2-20 skips that. It uses two separate analog delay lines, each modulated independently, to mimic two tape machines running at slightly different speeds. Instead of a single notch sweeping up and down, you get overlapping, shifting phase cancellations that evolve over time. The motion is less predictable and avoids the "whooshing" monotony of traditional phasing. Engineers who used it on drum overheads in the late '70s noted how it added depth without muddying the transients.
Variable Modulation Rate and Depth
The front panel offers straightforward controls for modulation rate and depth, but their range and smoothness set the DM2-20 apart. The rate can be dialed from nearly static to a fast, fluttery wobble, while the depth adjusts how far the simulated tape speed deviates from center. What makes this compelling is the interplay between the two: at low rates and high depth, you get a slow, seasick sway that’s perfect for ambient textures; at higher rates with moderate depth, it delivers a tight, pulsing rhythm that locks into the groove. Unlike many digital effects that followed, there are no presets—just knobs and real-time manipulation. This forces a hands-on approach, but also rewards experimentation. The lack of digital memory isn’t a limitation; it’s part of the charm. You tweak, you listen, you commit.
True Stereo Operation
Many effects units of the era were mono-in, stereo-out or pseudo-stereo at best. The DM2-20 was designed for true stereo operation from the ground up. The dual delay lines can be linked or modulated independently, which allows complex stereo imaging. In stereo mode, the phase shifts between left and right channels create a sense of movement, like sound circling around the listener. That made it a favorite for stereo synth passages and wide vocal doubles, where it could add separation without artificial panning tricks. Most studios were still mixing in mono or crude stereo at the time.
Historical Context
The DM2-20 arrived in 1976, when digital audio was still a fringe concept, mostly confined to research labs and high-end broadcast facilities. Most studios relied on plate reverbs, spring tanks, and tape echo machines for time-based effects. Digitally simulating tape artifacts was radical. Mark Crabtree, an aerospace engineer by training, applied the same rigor to audio design that he did to flight systems: clean layouts, sturdy power supplies, and careful signal paths. The DM2-20 wasn't a prototype. It showed that digital processing could enhance the warmth of analog recording rather than replace it.
It also preceded the digital explosion of the 1980s. The DMX 15-80, released two years later, would go on to define the sound of '80s pop with its pitch-shifting and delay capabilities, but the DM2-20 laid the groundwork. It showed that digital signal processing could be musical, not clinical. Competitors like Eventide were exploring similar territory with the H910 Harmonizer, but their focus was on pitch and time manipulation, not tape emulation. The DM2-20 carved out its own niche, one that was more about texture than transformation.
And while it never achieved mass-market success, its influence was quietly profound. Studios that owned one—Abbey Road, Townhouse, AIR—used it sparingly but decisively. It wasn’t a workhorse; it was a secret weapon. When Paul McCartney used AMS gear in the late '70s, he wasn’t just endorsing a product—he was validating a philosophy. As he put it, working with AMS units made him feel “as excited with the kind of possibilities as we had in the very early Beatle days.” That sentiment speaks volumes. The DM2-20 wasn’t just another box. It was a gateway to new sonic possibilities, built by someone who understood both the science and the soul of music.
Collectibility & Value
Finding a working DM2-20 today is hard. These units were never produced in large numbers, and few survived decades of studio use, power surges, and component aging. The analog delay lines are prone to drift and noise as capacitors degrade and op-amps wear out. The internal power supply, though well designed, can fail silently, taking other components with it if not addressed. Service technicians observe that the most common failure points are the electrolytic capacitors in the power regulation circuit and the modulation oscillator, which can drift out of spec, causing uneven or stalled phase sweeps.
Condition is everything. A recently serviced unit, especially one restored by a specialist like David Kulka or Studio Electronics, can command between $1,800 and $2,500, depending on provenance and included documentation. Unserviced units often sell for $800 - $1,200, but that price assumes the buyer has access to a qualified tech and is willing to risk a costly repair. Units with original manuals and schematics (like those offered by Studio Electronics) are particularly valuable to collectors, as they simplify troubleshooting and alignment.
When buying, test for smooth modulation across the full range, check for hum or noise in the output (especially at high gain settings), and verify that both channels behave identically in stereo mode. The XLR and 1/4" jacks should be secure, and the front-panel knobs should turn smoothly without crackling. Given its age, any DM2-20 should be considered a project unless verified as recently serviced. That said, for the right buyer—a studio owner chasing that elusive '70s texture, or a synth enthusiast building a period-correct rack—the DM2-20 isn’t just a purchase. It’s an investment in a sound that no plugin has fully captured.
Similar items on eBay
No exact AMS RMX DM2-20 listings are live right now — these searches show current AMS and similar vintage synth gear on eBay:
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.