Sony CA-TX7 Camera Adaptor
A broadcast triaxial dock that turns a boxy studio camera into a long-cable workhorse — and one of the least-documented links in Sony's professional chain.
Overview
The CA-TX7 is not a camera. It is the camera adaptor that docks with a DXC-D30/D30P or DXC-637 series Color Video Camera and connects it to a CCU-TX7/TX7P Camera Control Unit over triaxial cable. Sony's own manual describes the job plainly: the adaptor lets the camera talk to the control unit across a triaxial run, transferring the Y, R–Y and B–Y component signals for high picture quality rather than a composite compromise. That component-transfer detail is the whole point of the piece — it is the difference between a camera tethered to a control room and a camera feeding a monitor with a single wire.
The numbers that matter here are cable lengths. According to the operating manual, the maximum triaxial cable length between adaptor and control unit is 750 m with a Belden ø8.5 mm cable, or 1125 m with a Belden ø13.2 mm cable. That is over a kilometer on the fatter cable — the kind of reach that lets a camera sit at the far end of a stadium or a studio floor while the control unit stays in the rack room. Owners who work multicamera broadcast setups will recognize immediately what that spec is for.
Power is equally flexible, and this is where the CA-TX7 earns its keep on location. Fed through the CCU connector it runs on 120 V AC; fed through the DC IN connector it runs on 12 V DC (10.5 to 17 V DC). The adaptor also offers a DC OUT 4-pin connector delivering DC 12 V at a maximum of 12 W, intended for a WRR-810A UHF Portable Tuner or an LCD teleprompter unit. The manual is blunt about the limit: never connect a unit rated above 12 W. That is a real constraint for anyone trying to hang modern accessories off a period adaptor.
The input/output roster is professional-grade and specific. There is a Kings triaxial connector (made by Lemo) on the CA-TX7, while the CA-TX7P variant uses a Fischer triaxial connector. Prompter out and return out are both BNC at 1.0 Vp-p, 75 Ω. Intercom/program is a 5-pin XLR with an input level of –60 dBs (dynamic) and output level from –∞ to +12 dBs. Two mic inputs are 3-pin XLR female, 600 Ω balanced, switchable between –60 dB microphone level and –20 dB line level. A 10-pin DATA connector carries lens focus/zoom and tripod head pan/tilt control signals from a remote panel at the control unit. And the camera side terminates in either a PRO 76-pin DIGITAL or PRO 50-pin connector.
Two safety and convenience features are worth calling out because they speak to how the unit was actually used. An electrical shock prevention function shuts off the high-voltage supply whenever the connection is incomplete — a small thing until someone is plugging triaxial cable in the dark behind a rack. And a BREAKER button cuts power on a source or connection fault; once the problem is resolved, pressing it resets the breaker. The manual advises contacting a Sony dealer if the breaker trips again after the connection is corrected.
The POWER switch has three positions that reflect the two ways the adaptor can be fed: EXT for power via an optional CMA-8A/8ACE AC Adaptor on the DC IN connector (used when connected to the control unit by coaxial cable), CCU for power supplied through the camera control unit over triaxial, and OFF. Notably, when running over triaxial, intercom communication, back-tally on/off control (with the TALLY switch on), and CALL button paging all keep working even after the power is switched off. That is a deliberate design choice for a live production environment — the operator can still talk and be paged when the camera itself is dark.
Physically it is a compact, dense lump: approximately 2.7 kg (5 lb 15 oz), with external dimensions of 226 × 221 × 131 mm (w/h/d). Operating temperature spans –10ºC to +45ºC (14°F to 113°F) at 20% to 90% humidity, and it stores from –20ºC to +60ºC. Those are working-tool ratings, not living-room ratings — this is gear built to sit on the back of a camera in a cold outside-broadcast truck or a hot studio floor.
Power consumption figures depend entirely on what is hanging off the adaptor. Via the CCU connector, the CA-TX7/TX7P alone draws 10.5 W; docked with a DXC-D30/D30P that rises to 11 W (23.7 W total including the camera); adding a DXF-701/701CE viewfinder brings it to 11.2 W (26 W total); adding a DXF-51/51CE instead gives 12.3 W (35 W total). Outputting 12 W from the DC OUT connector while running a DXC-D30/D30P and DXF-51/51CE pushes the adaptor to 13.3 W and 48 W system total. Via the DC IN connector the adaptor itself sits at 7.5 W regardless of load, with the connected-equipment column climbing from 20.2 W to 42.2 W depending on the same combinations. Sony notes that the figure on the name plate is the total consumption of the adaptor outputting 12 W from DC OUT plus the DXC-D30/D30P and DXF-51/51CE.
Collectors and working shooters should understand what this thing is and is not. It is a system component, useless without the matching camera, control unit, and triaxial cable — and the manual lists the triaxial cable (Belden CCQX-3), DC power cord CMA-8A/8ACE, AC adaptor, and WRR-810A tuner as accessories not supplied. It also notes that converting the triaxial connector to accept a coaxial cable requires refitting and a consultation with a Sony dealer. So a loose CA-TX7 on a shelf is a puzzle piece, not a camera. What the documentation does establish is a serious, long-reach broadcast adaptor with component signal transfer, real cable-length capability, and a connector set built for the control room — the kind of unglamorous link that made the cameras it served actually usable.
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.