Yamaha M1516A
One hundred forty-seven pounds of Yamaha's workingman's console — a 16-channel M1500-series mixer that showed up in clubs, churches, and broadcast booths and quietly outlasted most of them.
Overview
The M1516A is the 16-channel member of Yamaha's M1500 mixing console family, and its spec sheet reads like a mission statement for the working sound reinforcement market. The console measures 34 inches wide, 36½ inches deep, and 14½ inches high, and it weighs 147 lbs — numbers that tell an owner a lot before they ever lift it. This is a board built to sit in a fixed installation or to be moved only when the job demands it, and the depth figure in particular signals a large, fully-featured channel strip rather than a compact club mixer.
Yamaha's own literature positions the M1500 series squarely at "just about any fixed or portable sound reinforcement or broadcast application," and the frequency response spec backs the broadcast claim: the M1516A is rated +0, −3dB from 20Hz to 20kHz, and tighter still at +0, −0.5dB from 30Hz to 15kHz. That flat-to-the-edges response is the kind of figure that matters when a console is feeding a broadcast chain or a recording rig rather than just a house PA.
The noise floor is where these consoles earned their reputation. Yamaha rates Equivalent Input Noise at −128dBm, and residual output noise with all faders down at −95dB. Program out sits at −73dB (77dB signal-to-noise) with the master fader at nominal and all input faders down, and −64dB (68dB S/N) with one input fader also up at nominal. The matrix outputs carry the same −73dB and −64dB figures under equivalent conditions, and the feedback/echo outputs come in at −70dB and −64dB. Those are quiet numbers for a console of this vintage, and they explain why so many of these boards ended up in houses of worship and installs where a hiss-free idle was non-negotiable.
Distortion is specified conservatively: less than 0.5% THD at +10dB from 20Hz to 20kHz, and less than 0.1% at +20dB from 50Hz to 20kHz. Note that both figures are measured with a 6dB/octave filter at 12.47kHz, which Yamaha describes as equivalent to a 20kHz filter with infinite attenuation — a detail that matters to anyone comparing the spec against a modern analyzer's unfiltered reading.
The channel strip carries a genuinely flexible four-band EQ with ±15dB of range. The low band is shelving with selectable turnover at 50, 100, 200, 350, or 500Hz. Low mid is peaking at 250, 350, 500, 700, or 1000Hz; high mid is peaking at 1.2, 2, 3.5, or 5.7kHz; and the high band is shelving at 10kHz. There's also an 18dB/octave high-pass filter rolling off below 80Hz, which is exactly the tool an owner wants for cleaning up stage rumble and proximity effect on vocals. Gain structure is generous: program and matrix paths offer 84dB maximum voltage gain from channel in to the corresponding output, the effects path offers 20dB from effects in to program out, and the feedback/echo path tops out at 94dB from channel in to FB/ECHO out. The sub input contributes 10dB into the program bus.
Phantom power is handled the way a working console should handle it: +40V DC is switched globally from a rear-panel master switch, and an individual input's phantom switch then applies that voltage to pins 2 and 3 of its balanced XLR. That two-stage arrangement is a small thing that owners appreciate, because it lets a single condenser be powered without committing the whole board.
The M1516A is one of three consoles in the series sharing the same performance and the same remote rack-mounted power supply arrangement. The 24-channel M1524 measures 55¼ inches wide and weighs 213 lbs; the 32-channel M1532 is 55¾ inches wide and weighs 231 lbs. The channel count is what changes across the line — the height stays put, which is convenient for anyone planning a rack or a road case around the family.
Period coverage of the console was largely spec-sheet driven. Mix (February 1985, p.24) and Recording-Engineer (April 1985, p.94) both ran the M1516A's general specifications — the same 20Hz–20kHz response, the same sub-0.5% and sub-0.1% THD figures, and the same −128dBm EIN — a reminder that in the mid-1980s this was a console being presented to the trade on the strength of its numbers rather than a long-form listening review. Sound and Communication (August 1985, p.18) carried the same specification block, which suggests Yamaha was pushing the M1500 series across the pro-audio press in a coordinated way that year.
What the spec sheet doesn't tell you is how the thing actually lives in a room, and that's where the M1516A's reputation was made. The deep, heavy chassis houses a layout with dedicated matrix and feedback/echo outputs — not an afterthought aux send, but a proper output section with its own level structure — and the four-band EQ gives an engineer real corrective power without resorting to outboard. The 147-lb weight is the price of that iron, and it's the reason these consoles tend to stay where they're installed.
Collectors and installers chasing an M1516A today should expect to find them in exactly the places Yamaha's own copy named — studios, concert halls, clubs, theatres, churches — and should budget for the remote rack-mounted power supply, which is part of the package and not an optional accessory. The console's value is in its quietness and its build, not in rarity; these were made to work, and many of them still do.
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.