Langevin TR-100

A ten-dollar circuit board that turned a hobbyist's workbench into a licensed CB station — if you fed it nine volts and a crystal.

Overview

The TR-100 was never a finished product in the way a receiver or a tape deck was. The buyer supplied the power supply, the modulator, and the enclosure. What the board did, per Round Hill's own catalog copy, was transmit: a complete crystal-controlled three-transistor Citizens' Band transmitter, pre-tuned at the factory for any CB channel and listed at $10.95.

The RF section is specified at 100 mW into a 50-ohm load, and the board runs on 9 volts DC at 50 mA. Those numbers are modest — 100 milliwatts is squarely in the legal CB power class of the period — but they're honest, and the catalog copy describes the output as "in excess of 100 MW," which is the kind of hand-waving every module maker did. The physical footprint was small enough to tuck almost anywhere: roughly 5½ inches long, 1¾ wide, and 2 high, with the weight left blank in the spec block. Additional CB crystals ran $3.00 each, so retuning to a different channel was a matter of swapping a rock rather than buying another board.

Modulation is where the TR-100 got interesting, and where Round Hill's ecosystem logic shows. The board supports CW or AM, but AM requires an external modulator — specifically the AA-100 Utility Amplifier, which the catalog explicitly names as the companion piece. The AA-100 was a 200 mW amplifier with a mounted volume control, general-purpose in intent, and it doubled as a modulator for the TR-100. For more ambitious builds, the AA-300 Professional Amplifier — also 200 mW but with the frequency response and distortion figures Round Hill pitched at broadcast, recording, and TV work — could drive the TR-100 as well. Power came from a battery or from the PS-300 supply, a zener-referenced regulated unit delivering 9 volts DC fully regulated at up to 200 mA, plus an unregulated 14-volt rail, for $18.95.

The catch, and it's a real one, is that the TR-100 was a component in a system that no longer exists as a system. Round Hill's own literature frames the whole line as "Instant Audio" — finished solid-state modules for building intercoms, mixers, monitors, language labs, and radio-controlled systems. The TR-100 was one brick in that wall, priced to move and documented in catalog pages rather than full service manuals. Collectors who find one today are typically looking at a loose board with no case, no supply, and no modulator, which means the practical path to hearing it transmit runs through sourcing a PS-300 or a clean 9-volt feed and an AA-100 or equivalent modulator. The BC-10 steel case, at $5.95, was a separate line item and is correspondingly rare on the secondary market.

A note on the paper trail: the period magazine chunks that surface for "TR-100" are a trap. DB-Magazine (September 1970, p.30) describes a Model TR-100 tape transport with bi-directional foil-contact operation — a completely different product from a different manufacturer, and it should not be conflated with the Round Hill transmitter board. The same caution applies to the recording-studio trade advertising in Recording-Engineer (August 1971, p.22), which is console-shop copy with no bearing on this board. The TR-100's own documentation is the Round Hill catalog sheet, and that's where the usable facts live.

What the board represents, more than any single spec, is the module era's economics: a $10.95 transmitter, a $7.95 modulator amp, an $18.95 supply, and a $5.95 case — under forty-five dollars to assemble a functioning CB transmitter from parts, at a time when finished transceivers cost multiples of that. The three transistors and the crystal are the whole story; there's nothing in there to go quietly obsolete. The hard part is everything around the board.

eBay Listings

SHOP LANGEVIN TR-100 ON EBAY

As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.