Kenwood TS-700SP
A 2-meter all-mode box that reads frequency to 100 Hz on a blue fluorescent panel and still wants a relay repair before it behaves.
Overview
The TS-700SP is Kenwood's fully solid-state, 2-meter all-mode amateur transceiver — a VHF base station that covers 144–148 MHz and does SSB, CW, FM, and AM from one chassis. That mode spread is the whole point. Plenty of 2-meter rigs of the era were FM boxes with a token nod to weak-signal work; this one was built to move between a repeater roundtable and a CW contact without changing radios. The manual is blunt about the architecture: the receiver runs as a single-conversion superheterodyne in SSB mode and a double-conversion superheterodyne in FM, while the transmitter is single conversion, operating as a filter-type unit in SSB, a variable-reactance frequency-shift unit in FM, low-power modulation in AM, and block bias keying in CW. That's a lot of circuit switching under one hood, and it explains why alignment matters so much on these.
The tuning is where the TS-700SP earns its keep. It carries a built-in VFO that continuously covers 144.00 to 148.00 MHz in four bands, and a dual vernier control splits the work: one knob gives bandspread tuning at 25 kHz per turn, the other tunes at 100 kHz per turn. Owners who work weak signal appreciate that kind of gearing — you can crawl across a crowded band segment without overshooting, then spin quickly to the other end. Repeater operation is possible in the 145, 146, and 147 MHz bands, with the shift available at both NORMAL and REVERSE positions of the repeater control knob, and the manual specifies a ±600 kHz shift with carrier-controlled and tone-burst starting.
The front-panel counter is a genuine selling point. It reads directly to 100 Hz in seven digits on a blue fluorescent display, showing actual operating frequency in any mode — including when you're driving the rig from the VFO-700S external VFO. The manual slips in a detail worth knowing: in CW mode the receive frequency includes the beat frequency and displays 900 Hz higher than the transmit frequency, and it does not indicate RIT offset. A sub-dial reads 100 kHz divisions as a rough reference alongside the exact digital readout. It's the kind of two-tier tuning display that feels fussy until you've used it, and then it feels indispensable.
Physically it's a desk radio, not a go-kit. The manual lists dimensions of 10-7/8" × 4-7/8" × 12-5/8" and a weight of 11.0 kg (24.2 lbs); the fact sheet's more rounded figures run approximately 330 × 125 × 300 mm and about 10.5 kg (23 lbs). Either way, it's a substantial piece of gear that wants a shelf, though the TS-700SP does carry self-contained AC and DC supplies for fixed-station or mobile operation. Power consumption is modest by modern standards — the manual gives 48 W on receive with no signal at 120/220V AC (1.2A at 13.8V DC), while the fact sheet's broader estimate runs about 30 W on receive and 150 W on transmit depending on mode and output.
Key Features
Blue Fluorescent Seven-Digit Counter
The built-in digital frequency counter is the feature that dates this radio to a specific moment in ham gear — and the one that still delights. It reads precise to 100 Hz across seven digits on a blue fluorescent display, showing actual operating frequency in any mode rather than a dial approximation. The manual notes it also displays your operating frequency when using the VFO-700S external VFO, which means the counter stays honest even when you hand tuning duties to an outboard unit. A separate sub-dial handles 100 kHz divisions for quick approximate reading, leaving the digital display for exact work. For a 2-meter rig where the interesting activity is packed into narrow slices of a 4 MHz band, that resolution is not a luxury.
Dual Vernier Tuning, 25 kHz and 100 kHz Per Turn
Two tuning rates on one control assembly: bandspread at 25 kHz per turn for fine work, and 100 kHz per turn for getting around. The manual describes it as a dual vernier tuning control, and it's the mechanical answer to a problem the digital display only partly solves. You can tune a weak SSB signal by ear at the slow rate, then reach across the band at the fast one. The built-in VFO covers the full 144.00 to 148.00 MHz continuously in four bands.
Ten Watts on 2 Meters, Three on AM
RF output is 10 W on SSB, CW, and FM, dropping to 3 W on AM — the manual also lists an FM Low setting of approximately 1 W. The final amplifier uses two 2SC1306 transistors as solid-state finals. Spurious radiation is rated better than −60 dB, and modulation is balanced for SSB, variable-reactance frequency shift for FM, and low-power modulation for AM. Maximum FM deviation is ±5 kHz, carrier and sideband suppression are each better than 40 dB, and AF response runs 400 to 2,600 Hz. Ten watts on 2 meters is a working man's output — enough with a decent antenna, not enough to paper over a bad feedline.
Receiver: 0.3 µV on SSB/CW, Switchable Preamp
The receiver is a double-conversion superheterodyne, with the manual specifying a 10.7 MHz IF for SSB, CW, and AM, and a 10.7 MHz first IF plus 455 kHz second IF in FM. Sensitivity is quoted at 0.3 µV for 10 dB S+N/N on SSB/CW (roughly −115 dBm) and 0.5 µV for 12 dB SINAD on FM (roughly −113 dBm). Selectivity is 2.4 kHz on SSB, 15 kHz on FM, with a 500 Hz CW filter listed as optional. Image and IF rejection are both rated at 60 dB or better. There's an R-DX receive preamp switch that boosts the RF stage by several dB for weak signals — and the manual is refreshingly honest that doing so makes the receiver more susceptible to cross-modulation and blocking from strong signals, and that the booster amplifies external noise along with everything else. Use it when you need it, not by default.
IF Shift, RIT, and a Real Noise Blanker
IF shift is available on SSB and CW only, for sliding the passband away from an adjacent signal. RIT gives ±5 kHz of receiver incremental tuning, and the manual's CW note — that the display shows receive frequency 900 Hz above transmit and does not reflect RIT offset — is the sort of detail that prevents a lot of confusion on the air. AGC is selectable Fast, Slow, or Off, and the noise blanker is switchable. There's also a tone pad input for auto-patch operation, and the repeater tone burst runs 0.5 to 1.0 second when the TONE switch is on and the rig is keyed in FM, with the tone oscillator element (optional) plugging into a socket on the FM IF unit.
Built-In AC Supply Plus 13.8 VDC Input
The TS-700SP carries a built-in 120/240 VAC supply and accepts 13.8 VDC through an external DC input on a heavy-duty cable — the DC supply is external, not built-in, which is the more precise reading of the documentation. The manual lists 48 W consumption on receive with no signal at 120/220V AC and 1.2A at 13.8V DC. Rear-panel connections include an SO-239 RF output at 50 ohms, a remote control port for an external VFO or frequency control, an 8-ohm external speaker jack (RigPix identifies the connector as a 3.5 mm TS minijack), a CW key jack, an accessory port for TNC, audio in/out, mute, and other interfaces, and the DC power input. Antenna impedance is 50 ohms.
VOX, Speech Processor, and FM Memory Channels
The feature list includes VOX and an adjustable speech processor, multiple memory channels for FM use, FM deviation adjustment, and a switchable antenna preamp and attenuator. The manual's block diagram counts the internals at 100 transistors, 19 FETs, 20 ICs, and 171 diodes, with circuits divided into individual units and all units except the band-pass filters wired on printed-circuit boards. The microphone impedance is low, 500 ohms per the manual's transmitter section (the fact sheet lists 600 ohms as standard for a dynamic mic), and the optional MC-50 communication microphone is switchable between 50 kΩ and 600 Ω, to be set at the low-Z position.
Collectibility & Value
Documentation on the TS-700SP is better than its market data. Current prices simply aren't established in the available sources, so anyone shopping should treat asking prices as unverified. What is documented is the maintenance picture, and it's specific: older units may suffer from display issues or aging electrolytic capacitors, and accurate alignment of the VFO, BFO, and filters is key to good SSB performance. The display is the counter — the blue fluorescent panel — so a dim or dead readout is the first thing to check on a candidate unit.
The repair literature is unusually concrete for a rig of this age. A "Kenwood TS-700SP receiver repair" article is dated 21 August 2018, and a "Kenwood TS-700SP antenna to receive / transmit relay repair" is dated 28 February 2023; a documented TS-700SP TX/RX relay repair procedure also exists in video form. That relay is worth knowing about before buying — it's a known service point, not a mystery. Paperwork is obtainable: a full 73-page printed service manual covering the TS-700S/TS-700SP and a 27-page instruction manual are both listed, and a service manual copy sells for $9.99. One caution for parts hunters: at least one "Kenwood TS-700S Original S Meter" is sold under the TS-700SP category, so verify the model label before assuming a part drops in. The TS-700S and TS-700SP are treated as the same family in some listings, and the available documentation doesn't settle whether their specs are interchangeable.
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.