Gates BC-1G (1962)
Gates built the "Big G" to run a small AM station at 1,000 watts and cut back to 250 — and half a century later, hobbyists are still hauling them out of Kentucky transmitter shacks and firing them up on 160 meters.
Overview
Gates sold the BC-1G as a "1000/250 watt broadcast transmitter" with switchable power output, and the 1962 catalog calls it the "Big G." That name is doing a lot of work: this is a full kilowatt medium-wave box, built around a pair of 833A triodes running in parallel, that a small station could dial down to 250 watts for nighttime operation. The catalog is explicit about how the cutback works — "switching in the primary of the main plate transformer eliminates power consuming and heat generating voltage dropping resistors" — which is a polite way of saying the Big G doesn't cook itself to lose three-quarters of its output.
The frequency coverage ran from 540 Kc to 2000 Kc, and the transmitter was designed for both 50 and 60 cycles of line power, with the catalog claiming a "20% bonus safety factor for 60" cycles. Primary input was 230V. Those are the numbers a station engineer cared about in 1962, and they're the numbers that make the BC-1G usable today: it's a medium-wave transmitter that a determined hobbyist can actually power and load into an antenna.
What the BC-1G is not, in the surviving documentation, is a well-specified piece of equipment. No dimensions, no weight, no original price, no THD figure, no frequency response — none of it survives in the material the archive has been able to decode. What does survive is the operating picture: a 1 kW transmitter with a 250-watt cutback, an 833-based final, and a reputation for being everywhere. One restorer's account notes that "at one time this basic design was so common that it seemed most small AM stations had one," and an amfone poster calls the BC-1 series "probably the most plentiful." Plentiful is the right word for a transmitter that turns up in barns, back rooms, and small-market stations with the regularity the BC-1G does.
Key Features
Two 833A Triodes in Parallel
The heart of the BC-1G is a pair of 833A triodes in the final, run in parallel. Engineering Radio describes the BC1G as "a pretty simple unit using 833A tubes in parallel with 3,500 VDC plate voltage," and a Radio World piece on the BC-1 series puts the RF power amplifier tube voltage at 2600 volts. Those two figures don't agree, and the archive has no way to reconcile them from the surviving documents — treat the plate voltage as being in the 2,600–3,500 VDC range depending on the source and the measurement point. What is not in dispute is the tube type: Gates stuck with the 833 triode "long after RCA, CCA, and McMartin were building similar transmitters with 4-400 tetrodes," which tells you something about how conservative the design was even in its own era.
Solid-State Rectifiers — a First for the Line
According to one restorer's account, the BC-1G "was the first model to use modern solid-state rectifiers rather than tubes." That's a meaningful shift for a transmitter of this class: it removes a whole category of tube-rectifier failure and heat from the power supply, and it's one of the reasons BC-1Gs are still being brought back to life rather than parted out. The same account notes that "those early diodes were fragile compared to today's parts, so they were replaced" during restoration — early solid-state was not the same as modern solid-state, and a working BC-1G today probably has newer diodes in it than it left the factory with.
Swing-Out Hinged Chassis
Unlike the earlier BC1T, the BC-1G "featured a swing-out hinged chassis for much of the circuitry." The same restorer adds a practical note that will ring true to anyone who has worked inside one: "it is much easier to remove the right-side panel for better access." The hinged chassis is the kind of feature that only matters when you're standing in front of the thing with a meter in your hand, and it's the difference between a transmitter you can service and one you can't.
PI-L-C-L Output Network
The original output network was a PI-L-C-L configuration, "with two of the coils being the front-panel rotary variables." That's a period-typical medium-wave tank, and it's also the part of the transmitter most likely to have been modified by a previous owner. The restorer quoted here converted his to a PI-L and built a toroidal current sensor, which is the sort of change that makes the transmitter more usable on the ham bands but takes it further from original. Buyers should expect the output network to be the most-modified section of any surviving BC-1G.
Tube Lineup: 833, 807, 12BY7A
Beyond the 833A finals, the documented tube complement includes an 807 as the RF driver and a 12BY7A in the buffer stage. The 807 driver is worth flagging because the Millen tube shields originally fitted to it "needed refinishing" on the restorer's unit — a small detail, but the kind of thing that tells you the shields are part of the transmitter's identity and worth preserving. The 12BY7A buffer is a small-signal tube, and its presence in the chain is a reminder that this is a 1960s design with a 1960s tube count throughout, not just at the output.
Companion Monitors: M-4990 and M-5693
Gates sold the BC-1G alongside two dedicated companion units: the M-4990 FCC-approved frequency monitor and the M-5693 FCC-approved modulation monitor (patent applied for). The 1962 catalog calls them "excellent companion units for the new BC-1G transmitter." They're not part of the transmitter itself, but they're the accessories a station would have bought with it, and a BC-1G that comes with either is a more complete package than one without.
Historical Context
The BC-1G dates to 1962, the date on the Gates catalog that describes it as "the new BC-1G transmitter." Archive.org's NRC document calls it "vintage 1960's," and Radio World places the BC-1 series within "this 1950 to 1970s technology." It sits in the middle of that span — late enough to have solid-state rectifiers, early enough to still be an 833-triode design.
The lineage is documented but not deep. The BC1T is named as the BC-1G's predecessor — one restorer calls it "it's father, the BC1T" — and the successor is described as "the same as well, excepting a solid-state crystal oscillator assembly." After that came the MW-1, which the same source calls "the world's first solid-state 1 kw broadcast transmitter." The BC-1G is therefore the first of the line to use modern solid-state rectifiers rather than tubes, and the direct ancestor of Gates' first solid-state kilowatt box.
RCA, CCA, and McMartin are named as the competitors building similar transmitters with 4-400 tetrodes. The BC-1G's niche was the small AM station — the kind of operation that needed a kilowatt by day and 250 watts by night, and that bought Gates because Gates was what the regional distributor stocked. Survivors turn up with station histories attached: one came out of WKDZ in Western Kentucky, another served WZAL/WJGA in Jackson, Georgia.
Collectibility & Value
There is no current market pricing data for the BC-1G in the archive's sources, and no original price survives either. What the archive does have is a restoration account detailed enough to serve as a buyer's guide, and the picture it paints is of a transmitter that is worth saving but not cheap to save.
The specific failure points named by the restorer are worth listing because they're the things to check before buying: the cylindrical filament sockets "were badly corroded"; of the tubes in the unit, "the two RF 833s on the right turned out to be the only tubes that were usable after the restoration"; "all of the high-voltage wire was old and brittle, just begging for disastrous arc-overs"; the 0-5 RF ammeter on the front panel "was burned out"; and there were "a few odd modifications which had to be undone, and a few failed connections." The audio driver-related capacitors and a number of bypasses were replaced, and the HV transformer on that unit was badly gouged during the move and had to be replaced from another similar transmitter — a reminder that these things are heavy and that moving one is its own project.
The upside is documented too. The same restorer's view is that "old broadcast transmitters (at least the smaller ones) make great ham AM units, operating very conservatively with clean audio," and he had his running on 160 meters by late December 2012 after starting in July of that year — roughly six months of work. Activity is cited around 1.885 and 3.885 MHz. Downloadable manuals for the BC-1G are hosted on the usual manual repositories, which is more than can be said for a lot of period broadcast gear. The BC-1G is not a rare transmitter and it is not a cheap one to restore, but it is a well-documented one, and that counts for a lot.
eBay Listings
As an eBay Partner, we earn from qualifying purchases. This helps support our independent vintage technology research.